Aicaigou LogoB2B WikiIndustrial Encyclopedia

VND5E050ACJTR-E

Updated: 2026-07-15

Overview

The VND5E050ACJTR-E is an automotive-grade power MOSFET manufactured to meet stringent reliability standards. It is part of a family of devices designed for high-current switching applications in harsh environments. As a surface-mount component, it integrates advanced protection features while maintaining compact dimensions suitable for modern electronic designs. This MOSFET is AEC-Q101 qualified, ensuring its suitability for automotive applications where temperature extremes and vibrational stresses are common. Its combination of performance and robustness has made it a preferred choice for automotive OEMs and industrial equipment manufacturers.

Structure and Working Principle

MT48LC16M16A2P-7EIT:G micron/镁光 存储IC TSOP-54 2021+ 电子元器件深圳市创芯联盈电子有限公司

The VND5E050ACJTR-E utilizes a vertical double-diffused MOS (VDMOS) structure that enables efficient current flow with minimal resistance. The device incorporates a charge pump for gate driving, allowing it to operate effectively at low voltage levels while maintaining fast switching characteristics. Internal protection circuits include current limiting, thermal shutdown, and open-load detection. These features work in concert to prevent device failure under fault conditions. The MOSFET's architecture is optimized for both switching and linear operation modes, providing flexibility in various circuit configurations.

商家经验真实案例 · 安全可信
xl1583芯片替代方案
本文探讨xl1583芯片的替代方案,包括功能兼容的芯片型号、替代时的注意事项以及如何评估替代方案的可行性,为工程师提供实用参考。

Key Features

With an exceptionally low RDS(on) of just 50mΩ, the VND5E050ACJTR-E minimizes power losses in conduction mode. It can handle continuous drain currents up to 5A, with pulse current capability significantly higher. The device operates across a wide temperature range from -40°C to 150°C, meeting automotive under-hood requirements. Integrated diagnostic features include analog current sensing and fault status reporting through dedicated pins. The device also incorporates advanced protection against reverse battery conditions, making it particularly suitable for automotive power distribution systems where such events may occur.

Application Areas

Primary applications include automotive body control modules, where it drives loads such as lighting, motors, and solenoids. The device is also widely used in power distribution units for advanced driver assistance systems (ADAS) and infotainment systems. Beyond automotive, the MOSFET finds use in industrial automation for controlling actuators and in power management circuits for portable equipment. Its reliability characteristics make it suitable for medical devices and other applications where failure is not an option.

Maintenance and Precautions

原厂 集成电路、处理器、微控制器 FXTH870502DT1 板机接口压力传感器 TPMS 7X7 450kPa Z axis深圳市安博威科技有限公司

While the VND5E050ACJTR-E is designed for reliability, proper PCB layout is crucial for optimal performance. Adequate copper area should be allocated for heat dissipation, and vias should be used to conduct heat to inner or bottom layers when necessary. Designers should pay particular attention to the gate drive circuit to ensure fast, clean switching transitions. The device's exposed pad must be properly soldered to the PCB for both electrical and thermal connection. When operating near maximum ratings, thermal analysis should be performed to verify junction temperatures remain within specified limits.

商家经验真实案例 · 安全可信
6sa7电子管连接方法
本文详细解析6sa7电子管的连接方法,包括引脚功能识别、典型电路配置及安全操作要点,帮助电子爱好者正确使用这款经典电子管。

B2B Procurement Guide

When sourcing the VND5E050ACJTR-E, verify the manufacturer's certificate of conformance and lot traceability information. Automotive applications typically require full PPAP documentation. Lead times can vary significantly based on market conditions, so establish relationships with authorized distributors or consider alternate sources during shortages. For high-volume purchases, negotiate pricing based on annual forecast quantities. Quality-conscious buyers should request production part approval process (PPAP) documentation and ensure suppliers can provide ongoing reliability monitoring data. Consider second-source options to mitigate supply chain risks.

Related Manufacturers