Aicaigou LogoAicaigou LogoB2B WikiIndustrial Encyclopedia

TLV62568DBVR

Updated: 2026-07-29

Overview

The TLV62568DBVR is a synchronous step-down DC-DC converter from Texas Instruments, designed for space-constrained applications requiring high efficiency. This compact IC operates with an input voltage range of 2.5V to 5.5V, making it suitable for single-cell Li-ion or multi-cell alkaline battery systems. With its integrated power switches and minimal external components, it simplifies power supply design while delivering up to 2A of output current. The device features a fixed-frequency PWM operation at light loads and automatically transitions to PFM mode at very light loads to maintain high efficiency across the entire load range. Its small SOT-23 package (DBV) makes it particularly attractive for portable electronics where board space is at a premium.

Structure and Working Principle

TLV62568DBVR 电源管理芯片 TI 封装SOT-23-5 批次21+深圳市龙宏电子科技有限公司

The TLV62568DBVR integrates two low RDS(on) MOSFET switches (high-side and low-side) along with control logic in a single chip. The converter operates on a current mode control architecture that provides fast transient response and good loop stability. During operation, the high-side switch charges the inductor during the on-time, storing energy in its magnetic field. When the high-side switch turns off, the low-side switch turns on, allowing the inductor current to flow to the output capacitor and load. The control circuitry adjusts the duty cycle based on the feedback voltage to maintain the desired output voltage. The device includes built-in protection features such as thermal shutdown, cycle-by-cycle current limit, and undervoltage lockout.

商家经验真实案例 · 安全可信
电源管理芯片解析
本文深入浅出地解析了电源管理IC芯片的基本概念、核心功能及应用场景,帮助读者快速理解这类电子设备中的‘能量管家’如何工作,以及为何它对现代电子产品至关重要。

Key Features

The TLV62568DBVR stands out for its exceptional efficiency, achieving up to 95% conversion efficiency across much of its operating range. Its ultra-low quiescent current (typically 15μA) significantly extends battery life in portable applications. The fixed 2.5MHz switching frequency allows for small external components while keeping switching noise out of sensitive frequency bands. Other notable features include 100% duty cycle operation (when input voltage approaches output voltage), soft-start to limit inrush current, and power-good output for system monitoring. The device maintains good line and load regulation, with typical output voltage accuracy of ±1.5% over line, load, and temperature variations.

Application Areas

This converter is particularly well-suited for battery-powered applications including smartphones, tablets, digital cameras, and portable medical devices. Its efficiency and small footprint make it ideal for IoT endpoints, wireless sensors, and wearable electronics where both power consumption and size are critical factors. Industrial applications include factory automation equipment, handheld test instruments, and distributed power systems. The wide input voltage range also allows it to be used in 3.3V or 5V bus-powered systems, serving as point-of-load converters for FPGAs, ASICs, and other digital ICs requiring clean, regulated power.

Maintenance and Precautions

TLV62568DBVR 电源管理芯片 TI 封装SOT23-5 批次24+深圳市新思汇科技有限公司

For optimal performance and reliability, proper PCB layout is essential. Place input capacitors close to the VIN and GND pins, using short, wide traces. The inductor should be positioned nearby, with the SW node kept as small as possible to minimize EMI. A ground plane helps with thermal dissipation and noise reduction. Avoid exceeding the absolute maximum ratings (6V on VIN, for example) as this can damage the device. Ensure adequate thermal management, especially when operating near maximum load current in high ambient temperatures. For applications with long cable runs or potential for voltage spikes, additional input protection may be necessary.

商家经验真实案例 · 安全可信
324芯片驱动发光二极管
本文详细解析324芯片驱动发光二极管的原理与实现方法,包括电路连接方式、电流控制技巧及常见问题解决方案,帮助读者轻松掌握LED驱动技术。

B2B Procurement Guide

When procuring TLV62568DBVR in quantity, consider lead times which can vary based on market demand - typically 8-12 weeks for standard orders. Verify the manufacturer's part number suffix to ensure you're getting the correct package (DBV for SOT-23-5). For high-reliability applications, request data on lot traceability and manufacturing date. Evaluate alternative sources carefully as counterfeit components are a concern in the semiconductor market. Approved distributors or direct purchases from the manufacturer offer the best assurance of authenticity. For prototyping or small quantities, sample kits are often available through manufacturer programs or authorized distributors.

Related Manufacturers