Aicaigou LogoAicaigou LogoB2B WikiIndustrial Encyclopedia

TLV3492AID

Updated: 2026-08-04

Overview

The TLV3492AID is a dual-channel, low-power operational amplifier from Texas Instruments, optimized for precision applications. It operates with a supply voltage range of 1.8V to 5.5V, making it suitable for battery-powered devices. The op-amp offers rail-to-rail output swing, ensuring maximum signal integrity in low-voltage systems. Designed for industrial and consumer electronics, the TLV3492AID is commonly used in sensor interfaces, portable medical devices, and audio processing circuits. Its low quiescent current (typically 20 µA per channel) extends battery life in energy-sensitive applications.

Structure and Working Principle

NCP308SNADJT1G 电源控制器/监视器 ON 封装SOT23-6 批次24+深圳市银海芯科技有限公司

The TLV3492AID integrates two independent op-amps in an 8-pin SOIC package. Each amplifier features a differential input stage followed by a gain stage and rail-to-rail output buffer. The device uses CMOS technology to achieve low power consumption and high input impedance. Its working principle relies on amplifying the voltage difference between the inverting and non-inverting inputs, with a typical gain bandwidth product of 1 MHz. The rail-to-rail output stage ensures minimal signal clipping, even at supply voltages as low as 1.8V.

商家经验真实案例 · 安全可信
nova 14
本文探讨了nova 14的相关信息,包括其功能特点、应用场景以及用户可能关心的其他方面,帮助读者全面了解这一主题。

Key Features

The TLV3492AID stands out for its ultra-low power consumption, drawing only 20 µA per channel, which is critical for portable and IoT devices. Its rail-to-rail output allows for full dynamic range utilization in low-voltage systems. Other notable features include a wide supply voltage range (1.8V to 5.5V), low input bias current (1 pA typical), and a high common-mode rejection ratio (70 dB). These characteristics make it suitable for precision analog circuits where signal integrity and power efficiency are paramount.

Application Areas

This op-amp is widely used in industrial sensors, such as strain gauges and thermocouples, due to its precision and low noise. In consumer electronics, it appears in wearable devices and audio amplifiers. Medical applications include portable diagnostic equipment and patient monitoring systems, where its low power consumption is advantageous. Additionally, it serves in automotive systems for signal conditioning in sensors and control modules.

Maintenance and Precautions

TLP5772(TP,E(O 电子元器件 TOSHIBA/东芝 数据手册 规格书深圳市光与电子有限公司

To ensure optimal performance, avoid exposing the TLV3492AID to supply voltages beyond 5.5V, as this may damage the device. Proper decoupling capacitors (0.1 µF) should be placed near the power pins to minimize noise. For PCB layout, keep traces short and avoid crossing high-frequency signals near the op-amp inputs to prevent instability. Thermal management is generally not required due to its low power dissipation, but adequate ventilation is recommended in high-density designs.

商家经验真实案例 · 安全可信
花生苗期微控时间
本文详细解答花生苗期微控的最佳时机及其科学依据,包括温度、湿度和光照等关键因素对花生幼苗生长的影响,帮助种植者掌握精准管理技巧。

B2B Procurement Guide

When sourcing the TLV3492AID, verify the manufacturer (Texas Instruments) and part number to avoid counterfeit components. Purchase from authorized distributors or trusted B2B platforms like Digi-Key or Mouser. Bulk orders (e.g., reels of 2,500 units) typically reduce the per-unit cost by 20–30%. Lead times vary but average 6–8 weeks for large quantities. For prototyping, consider sample kits offered by TI or distributors.

Related Manufacturers