Overview
Polystyrene core moulds are prefabricated foam elements designed for creating voids in concrete structures. Composed of expanded polystyrene (EPS), these moulds serve as temporary or permanent formwork in construction projects. They significantly reduce structural weight while maintaining design integrity. The material's closed-cell structure provides excellent buoyancy and thermal insulation properties. In construction, these moulds are typically left in place after concrete pouring, eliminating the need for formwork removal and reducing labor costs.
Physical and Chemical Properties
With densities ranging from 15-30 kg/m³, polystyrene core moulds offer an exceptional strength-to-weight ratio. The material demonstrates low thermal conductivity (0.033-0.037 W/mK) and high compressive resistance (50-140 kPa depending on density). Chemically, EPS is inert to most common construction materials including concrete, lime, and gypsum. It resists moisture absorption (0.5-3% by volume) but should be protected from prolonged UV exposure which may cause surface degradation. The material maintains dimensional stability between -40°C to 70°C.
Main Applications
Primary use includes void formation in concrete slabs, beams, and bridge decks where weight reduction is critical. The moulds create permanent cavities that decrease dead load by up to 35% compared to solid concrete sections. Secondary applications encompass insulation panels for buildings, floating platforms in marine construction, and packaging for fragile equipment. Specialized grades with fire retardants are available for projects requiring enhanced fire safety compliance.
Safety and Storage
While polystyrene is non-toxic in its solid state, proper ventilation is recommended during cutting to prevent inhalation of fine particles. Storage should be in covered areas protected from solvents, petroleum products, and temperatures exceeding 80°C. Fire safety precautions are essential - though some grades contain flame retardants, all EPS products are combustible. On job sites, maintain minimum 10m distance from welding operations and prohibit smoking near stored materials.
B2B Procurement Guide
When sourcing polystyrene core moulds, specify required density (typically 20-25 kg/m³ for structural applications), dimensional accuracy (±2mm tolerance is standard), and any special certifications (e.g., fire ratings). Lead times vary from 1-3 weeks for standard sizes; custom shapes may require additional time. Bulk orders (100+ m³) typically qualify for 15-25% discounts. Verify supplier capabilities for just-in-time delivery to minimize on-site storage needs.
Related Manufacturers
- 主营：预应力塑料波纹管、桥梁预应力波纹管、波纹管、一次性泡沫芯模、金属螺旋管、双臂波纹管、金属管、透水管、内衬管、止水带、碳素波纹管、泡沫芯膜、塑料扁管、一次性芯膜、桥梁穿线管、桥梁伸缩缝、预应力锚具、透水盲沟管、张拉力锚具、桥梁张拉锚具、金属波纹圆管、桥梁填充内模、预埋地脚螺栓波纹管
- 主营：桥梁伸缩缝、钢结构支座、桥梁橡胶支座、桥梁泡沫芯模、管道封堵气囊、橡胶止水带、固定铰支座、滑动支座、钢连廊支座、梳齿板伸缩缝、板式橡胶支座、密封胶、桥梁支座、D80型桥梁伸缩缝、高压封堵气囊、隔震支座、橡胶桥梁支座、桥梁泄水管、滚轴支座、双向滑动支座、单向滑动支座、GBZY橡胶支座、抗震支座、铰接支座、盆式支座、TST弹素体伸缩缝
- 主营：预应力波纹管、预应力塑料波纹管、预应力金属波纹管、泡沫芯模、公路桥梁填充芯模、桥梁泡沫芯模、装配式建筑芯模、碳素管、双壁波纹管、打孔波纹管、锚具、伸缩缝、pe内衬管、泡沫板、桥梁泡沫芯膜、PE双壁波纹穿线管、供应塑料pe波纹管、预应力桥梁金属波纹管、HDPE碳素波纹管、HDPE碳素管、PE碳素波纹管、碳素波纹管、桥梁泡沫内膜、桥梁预应力金属波纹管、桥梁预应力塑料波纹管
- 主营：塑料波纹管、预应力塑料波纹管、桥梁波纹管、桥梁泡沫芯模、泡沫芯模、空心板泡沫内模、波纹管、预应力波纹管、黑色螺旋波纹管、白竹节波纹管、塑料波纹管接头、桥梁预应力塑料波纹管、预应力金属波纹管、镀锌金属波纹管、金属波纹管、钢带波纹管、桥梁穿钢绞线波纹管、混凝土预应力波纹管、大口径预埋金属管、一次性桥梁内模、锚具、张拉锚具、预应力锚具
- 主营：钢纤维、混凝土、波纹管、泡沫芯模、桥梁空心板、遮缝板、卸落支架、减震装置、橡胶支座、桥梁伸缩缝、聚乙烯复合管、抗裂防渗钢锭、消能粘滞阻尼器
- 主营：波纹管、预埋穿线管、预埋穿线螺纹管、空心板泡沫芯模、充气芯模、接线箱、集水井、卸落块、护栏支架、桥梁伸缩缝
- 主营：塑料模芯、蜂巢芯、薄壁方箱、空心楼盖芯模、聚苯乙烯芯模、水泥砂浆芯模、建筑工程空心模、金属芯模、补强箱
- 主营：薄壁方箱、薄壁箱体、蜂巢芯、空心楼盖、建筑芯模、空心箱体、合金芯模、自承式芯模、钢网箱、装配箱、自承箱、PP方箱、建筑模盒、合金箱体、组合箱
- 主营：泡沫芯模、泡沫内模、桥梁泡沫内膜
- 主营：伸缩缝、钢模板、建筑钢材、空心板、泡沫芯模、钢板定制、防撞护栏、公路护栏、桥梁钢模、桥梁护栏、遮板模具、加厚钢板、涵洞模板、护栏模具、泡沫内模、拆除模具、景观栏杆、防撞栏杆、橡胶支座、不锈钢护栏、高架桥护栏、复合管栏杆、租赁平面模板、桥梁泡沫内膜、平面组合钢板
- 主营：装配箱、薄壁方箱、密肋楼盖、聚芯模、空心楼盖、空心薄壁管、聚苯填充棒、预应力空心板、桥梁芯模、EPS聚苯乙烯泡沫、空心内模、BBF空心薄壁管、空心叠合板、芯模、空心板泡沫芯模、GBF空心薄壁管、钢制网状构件、复合填充箱体、减重块、预应力钢管桁架、箱体、BDF钢网箱、一次性桥梁泡沫、聚合物筒芯
- 主营：桥梁支座、桥梁护栏支架、桥梁卸落块、泡沫芯模、橡胶支座、盆式橡胶支座、GPZ‖盆式支座