Aicaigou LogoAicaigou LogoB2B WikiIndustrial Encyclopedia

PIC16F87620/SO

Updated: 2026-08-05

Overview

The PIC16F876 is a mid-range 8-bit microcontroller from Microchip's PIC16F family, offering a balance of performance, power efficiency, and cost-effectiveness. It features 14KB of flash program memory, 368 bytes of RAM, and 256 bytes of EEPROM data memory, making it suitable for a wide range of embedded applications. Based on Microchip's enhanced CMOS technology, this microcontroller operates at speeds up to 20MHz with a wide voltage range (2.0V to 5.5V). Its 28-pin package includes multiple I/O ports, timers, and communication interfaces (USART, SPI, I2C), providing flexibility for various system designs.

Structure and Working Principle

ADS7800JU 模数转换器(ADC) Texas Instruments 封装24-SOIC 批次21+深圳市冠亿通科技有限公司

The PIC16F876 follows a Harvard architecture with separate program and data buses, allowing simultaneous access to program instructions and data. Its CPU core executes most instructions in a single cycle (4 clock cycles), achieving up to 5 MIPS at 20MHz operation. The microcontroller integrates several peripheral modules including five 10-bit analog-to-digital converter channels, three timers/counters, and multiple interrupt sources. Its in-circuit serial programming (ICSP) capability allows for easy firmware updates without removing the chip from the circuit board.

商家经验真实案例 · 安全可信
电磁炉双频与变频的区别
本文解析电磁炉双频与变频技术的核心差异,从工作原理、能效表现到适用场景,帮助用户理解两种技术的特点及选择建议。

Key Features

Key features of the PIC16F876 include its 8-bit RISC architecture with 35 single-word instructions, enhanced flash memory with 100,000 erase/write cycles endurance, and low-power consumption modes (typical standby current < 1μA). The device offers 22 I/O pins with individual direction control and programmable pull-up resistors. Special features include a built-in watchdog timer for reliability, brown-out reset for power management, and a capture/compare/PWM module for timing-critical applications. The microcontroller's wide operating voltage range makes it suitable for both battery-powered and line-powered applications.

Application Areas

The PIC16F876 finds extensive use in industrial control systems, automotive electronics, medical devices, and consumer products. Its analog capabilities make it ideal for sensor interfaces, while its communication peripherals enable networking in embedded systems. Common applications include motor control, power management systems, HVAC controllers, security devices, and small appliance control. The microcontroller's reliability and development tool support have made it popular in educational settings for teaching embedded systems concepts.

Maintenance and Precautions

PIC16F88-E/SO 电子元器件 MICROCHIP微芯 封装18 SOIC  批次21+深圳市海誉晟科技有限公司

When working with the PIC16F876, proper ESD precautions should be observed during handling and installation. The device should be stored in anti-static packaging when not in use, and work surfaces should be properly grounded. For programming and debugging, use only certified development tools and follow Microchip's recommended practices. The flash memory has a finite write/erase cycle life, so firmware should minimize unnecessary write operations. Power supply filtering and proper decoupling capacitors are essential for stable operation.

商家经验真实案例 · 安全可信
l10891e型号解析
本文针对l10891e型号的两种可能数值2900和3000进行解析,帮助用户明确该型号的具体参数差异及应用场景。

B2B Procurement Guide

When procuring PIC16F876 microcontrollers in bulk, verify the manufacturer's part number (PIC16F876-I/SP or similar) and packaging type (tube, tray, or tape-and-reel). Check for current RoHS compliance status and lead-free certification if required for your application. Consider purchasing from authorized Microchip distributors to ensure genuine components. For prototyping or small quantities, development boards and starter kits are available that include the microcontroller with necessary support components. Lead times may vary depending on market conditions, so plan procurement accordingly.

Related Manufacturers