Aicaigou LogoAicaigou LogoB2B WikiIndustrial Encyclopedia

Pervious Concrete Material

Updated: 2026-07-15

Overview

Pervious concrete is an engineered material consisting of carefully graded coarse aggregates bonded with Portland cement, with minimal fine aggregates to create an interconnected pore structure. Developed in the mid-20th century for specialized applications, it has gained prominence in modern sustainable construction due to its stormwater management capabilities. The material typically contains 15-25% void space, allowing water to percolate through at rates of 2-18 gallons per square foot per minute. Unlike conventional concrete, the absence of fine aggregates creates the characteristic porous structure while maintaining sufficient compressive strength for pedestrian and light vehicular traffic.

Physical and Chemical Properties

美桥 TS-128 透水路面喷漆 高粘度 性能好 包工包料 在线接单广东美桥景观建材有限公司

The physical properties of pervious concrete differ significantly from conventional concrete. Its density ranges from 1600-2000 kg/m³ depending on aggregate size and void ratio, compared to 2300-2500 kg/m³ for standard concrete. The compressive strength typically falls between 500-4000 psi, suitable for low-traffic applications but requiring reinforcement for heavier loads. Chemically, pervious concrete shares the same cementitious binder as conventional concrete, with calcium silicate hydrate (C-S-H) as the primary binding phase. The high porosity increases carbonation rates, potentially affecting long-term durability in certain environments. Special admixtures are often incorporated to enhance freeze-thaw resistance in cold climates.

商家经验真实案例 · 安全可信
沥青冷拌VS热铺的区别
本文从施工条件、材料特性和适用场景三个维度,生动解析沥青冷拌与热铺工艺的核心差异,帮助读者根据实际需求选择合适的道路铺设方案。

Main Applications

The primary application of pervious concrete is in sustainable urban drainage systems (SUDS). It's extensively used for parking lots, sidewalks, and low-volume roads where stormwater infiltration is desired. Municipalities increasingly specify it for LEED-certified projects to earn credits for stormwater management and heat island reduction. Beyond pavement applications, pervious concrete serves as a filtration medium in some water treatment systems and as a substrate for green roofs. Its thermal mass properties combined with evaporative cooling make it effective for urban heat island mitigation. Some agricultural applications include livestock walkways and greenhouse floors where drainage is critical.

Safety and Storage

透水混凝 土材料厂家 坤聚施工规范 露骨料透水混凝土材料价 格江苏坤聚建设有限公司

Fresh pervious concrete presents similar alkaline hazards as conventional concrete, requiring skin protection during placement. The high porosity increases surface drying rates, necessitating proper curing methods such as plastic sheeting or spray-applied curing compounds to prevent premature moisture loss. For material storage, cementitious components should be kept dry and protected from moisture. Bulk aggregates for pervious concrete mixes often require covered storage to maintain consistent moisture content. Pre-mixed materials typically have a shelf life of 6 months when properly stored in moisture-resistant packaging.

商家经验真实案例 · 安全可信
透水混凝土施工全攻略
本文系统介绍透水混凝土路面的材料选择与施工要点,包括骨料配比、添加剂使用、分层浇筑工艺及后期养护技巧,帮助读者掌握这种环保路面的关键技术。

B2B Procurement Guide

When procuring pervious concrete materials, specify the required permeability rate (typically 0.2-0.5 in./min), compressive strength, and freeze-thaw durability if applicable in your climate. Request mix designs that have been tested for clogging resistance, especially for high-sediment environments. For large projects, consider on-site batching to ensure fresh placement. Verify supplier experience with pervious concrete installations - specialized placement techniques differ from conventional concrete work. Request references for similar projects and inquire about warranty provisions for surface raveling or clogging issues. Bulk pricing typically becomes competitive for orders exceeding 100 cubic yards.

Related Manufacturers