Aicaigou LogoAicaigou LogoB2B WikiIndustrial Encyclopedia

MT48LC32M8A2BB-6A

Updated: 2026-07-15

Overview

The MT48LC32M8A2BB-6A is a Micron Technology synchronous DRAM component designed for demanding industrial applications. As a 256-megabit memory device organized as 32M words by 8 bits, it provides balanced performance for embedded systems requiring moderate bandwidth. The -6A speed grade indicates 6ns access time capability, making it suitable for real-time processing applications. This SDRAM operates at 3.3V with a fully synchronous interface, clocking up to 166MHz. It implements auto refresh (8192 cycles/64ms) and self refresh modes for power management. The component comes in a 54-pin TSOP II package, designed for surface mount assembly in industrial control systems and communication infrastructure.

Structure and Working Principle

MT29KZZZ6D4AGLDM-5 W.6N4 电子元器件 Micron/美光 批号最新批次深圳楷东科技有限公司

The MT48LC32M8A2BB-6A employs a four-bank architecture with synchronous interface timing. Each of the 32Mbit banks contains row and column address buffers that latch commands on the positive clock edge. The internal pipeline allows burst operations of 1, 2, 4, 8 or full-page length, programmable via mode register settings. Refresh operations maintain data integrity through either auto refresh commands or self refresh mode when the device is idle. The 6ns access time (CL=3 at 166MHz) is achieved through precise internal timing control and signal synchronization. The component includes input registers to reduce setup/hold timing requirements on the host system.

商家经验真实案例 · 安全可信
lm4765与lm4766区别
本文深入对比分析lm4765和lm4766两款音频功放芯片的关键参数差异,从输出功率、失真度到封装设计,帮助工程师快速匹配项目需求。

Key Features

Industrial temperature range support (-40°C to +85°C) makes this SDRAM suitable for harsh environments. The device offers programmable CAS latency (2 or 3 cycles) and burst lengths to optimize for different application requirements. Power consumption is managed through multiple low-power modes including clock suspend and power-down states. Notable features include single 3.3V ±0.3V power supply, automatic precharge option, and hidden refresh capability. The component meets JEDEC standard specifications for SDRAM operation while adding industrial-grade reliability features. Data integrity is maintained through ECC-supporting architectures when used in appropriate system designs.

Application Areas

This memory component is primarily deployed in industrial automation systems where consistent performance across temperature extremes is required. Common applications include PLCs, motor controllers, and test equipment that demand reliable memory operation in manufacturing environments. Telecommunications infrastructure represents another major application area, particularly in base station equipment and network switches where the 166MHz operation supports packet buffering needs. Automotive electronics systems also utilize this SDRAM grade for infotainment and telematics units that must operate across vehicle temperature ranges.

Maintenance and Precautions

JS28F00AP30EFA 存储IC Micron(镁光) 封装TSOP-56深圳市特立芯科技有限公司

Proper handling requires ESD protection measures during installation and maintenance. The TSOP package leads are susceptible to mechanical stress, requiring careful soldering and board mounting procedures. Signal integrity must be maintained through proper PCB layout with controlled impedance for clock and data lines. System designers should implement appropriate power decoupling (typically 0.1μF ceramic capacitors per power pin pair) to ensure stable operation. Refresh timing must be maintained according to specifications, with special attention during low-power modes. Long-term storage recommendations include moisture-sensitive packaging and baking procedures before reflow soldering.

商家经验真实案例 · 安全可信
lyt808和lyt700选哪个
本文对比分析lyt808和lyt700两款产品的性能特点,从工作效率、适用场景和用户反馈三个维度展开,帮助读者做出合理选择。

B2B Procurement Guide

Industrial buyers should verify the MT48LC32M8A2BB-6A's current lifecycle status with Micron, as industrial-grade components may have different availability than commercial equivalents. Lead times can vary significantly (typically 8-16 weeks), so forecast planning is essential. Consider minimum order quantities which commonly range from 500-1,000 pieces for industrial distributors. Evaluate alternative packaging options (tray vs. reel) based on production line requirements. Request factory traceability documentation for critical applications. For prototype or small-scale production, consider authorized distributors with inventory management programs. Always verify date codes to avoid obsolescence issues in long-lifecycle products.

Related Manufacturers