Aicaigou LogoB2B WikiIndustrial Encyclopedia

MT28F200B5SG-8

Updated: 2026-07-15

Overview

The MT28F200B5SG-8 is a 2-megabit (256KB) flash memory chip designed for industrial and embedded applications. It operates at 5V and provides non-volatile storage, making it ideal for systems requiring reliable data retention. Manufactured by Micron Technology, this chip is known for its robustness and fast read/write capabilities. Flash memory like the MT28F200B5SG-8 is widely used in scenarios where power interruptions must not result in data loss. Its architecture allows for efficient data access, making it suitable for real-time systems and high-performance computing environments.

Structure and Working Principle

MT28F200B5SG-8TE 电子元器件 镁光 封装SOP44 批号25+深圳市汇莱威科技有限公司

The MT28F200B5SG-8 utilizes NOR flash memory technology, which enables random access to memory locations. This is particularly useful for executing code directly from the flash memory, a common requirement in embedded systems. The chip is organized into sectors, allowing for efficient erase and write operations. Internally, the memory cells are structured in a grid, with each cell storing a bit of data. The 5V operation ensures compatibility with a wide range of legacy systems, though modern designs often prefer lower voltage alternatives for power efficiency.

商家经验真实案例 · 安全可信
mcf183芯片管脚功能
本文详解mcf183芯片各管脚的功能定义与应用场景,包括电源管理、信号输入输出及特殊功能引脚的设计逻辑,助您快速掌握该芯片的硬件连接要点。

Key Features

The MT28F200B5SG-8 offers several key features, including a 2Mb storage capacity and a fast access time, typically around 70-90 nanoseconds. Its 5V operation makes it compatible with older systems, while its industrial-grade temperature range (-40°C to +85°C) ensures reliability in harsh environments. Additionally, the chip supports block erase functionality, which allows for efficient memory management. This is particularly useful in applications where frequent updates to stored data are required, such as firmware storage in embedded devices.

Application Areas

This flash memory chip is commonly used in telecommunications equipment, automotive electronics, and medical devices. Its reliability and fast access times make it suitable for critical applications where data integrity is paramount. In automotive systems, the MT28F200B5SG-8 might store firmware for engine control units (ECUs) or infotainment systems. In medical devices, it could be used for storing calibration data or operational software, ensuring consistent performance over the device's lifespan.

Maintenance and Precautions

MT28F200B5SG-8TE 电子元器件 MICRON 封装SOP44 批次23+深圳市汇莱威科技有限公司

To ensure the longevity of the MT28F200B5SG-8, it is important to protect it from electrostatic discharge (ESD). Proper handling procedures, such as using grounded wrist straps and anti-static mats, should be followed during installation and maintenance. Additionally, the chip should be operated within its specified voltage range to prevent damage. Overvoltage can lead to data corruption or permanent failure, while undervoltage may result in unreliable operation.

商家经验真实案例 · 安全可信
cs8611e引脚功能解析
本文深入解析CS8611E芯片各引脚的功能与参数特性,包括电源管理、信号输入输出配置及典型应用场景,帮助工程师快速掌握该芯片的核心使用要点。

B2B Procurement Guide

When procuring the MT28F200B5SG-8, it is essential to verify the supplier's authenticity to avoid counterfeit products. Reliable distributors often provide traceability and certification for their components. Consider ordering in bulk to benefit from volume discounts, but ensure that the storage conditions (dry, temperature-controlled environments) are maintained to preserve the chips' integrity before use. Lead times can vary, so plan purchases accordingly to avoid project delays.

Related Manufacturers