Aicaigou LogoB2B WikiIndustrial Encyclopedia

MAX7323ATE+T

Updated: 2026-08-03

Overview

The MAX7323ATE+T is an I²C-interfaced peripheral device that provides 8 general-purpose input/output (GPIO) ports, designed to expand the I/O capabilities of microcontrollers in space-constrained applications. Manufactured by Maxim Integrated (now part of Analog Devices), this IC operates across a wide voltage range (1.7V to 5.5V), making it suitable for both low-power and standard logic level systems. As a port expander, it significantly reduces the number of physical connections required between a microcontroller and peripheral devices, particularly valuable in complex embedded systems. The device supports 400kHz I²C fast-mode communication and includes programmable pull-up resistors, offering design flexibility for various applications.

Structure and Working Principle

ES1D-E3/61T 快恢复二极管DIODE STANDARD 200V 1A VISHAY威世 DO-214AC深圳市元睿芯电子有限公司

The MAX7323ATE+T comes in a compact 16-pin TQFN package (3mm x 3mm), containing an I²C interface block, control logic, and eight GPIO ports with configurable direction registers. Each I/O can be independently programmed as an input or output through I²C commands, with input state detection and interrupt generation capabilities. The device operates as an I²C slave, responding to commands from a host microcontroller. When configured as inputs, the ports can trigger an interrupt output pin upon state change, reducing the need for continuous polling. Internal registers store the configuration and I/O states, which can be read or modified through standard I²C read/write operations, following the protocol's addressing and acknowledgment scheme.

商家经验真实案例 · 安全可信
装修电位计算指南
本文详细解析装修中电位的计算方法,包括电位的基本概念、计算步骤以及实际应用中的注意事项,帮助读者轻松掌握装修电位的核心要点。

Key Features

The MAX7323ATE+T stands out for its wide operating voltage range (1.7V-5.5V), allowing seamless integration with both 3.3V and 5V systems without level shifters. Its 8 GPIO ports feature 25mA sink/source capability, sufficient for driving LEDs or small relays directly. Notable features include programmable pull-up resistors (100kΩ typical) for each I/O pin, eliminating external components in many designs. The interrupt output pin (active-low) provides efficient event-driven operation, signaling input changes to the host controller. With a 400kHz I²C interface, it offers faster response times compared to similar SPI-based expanders in multi-device systems.

Application Areas

This IC finds extensive use in industrial automation for adding digital I/O to PLCs and control modules, particularly where physical I/O constraints exist. In consumer electronics, it's employed in smart home devices, appliance control panels, and gaming peripherals requiring additional buttons or status LEDs. Embedded system designers utilize the MAX7323ATE+T in space-constrained applications like wearable devices and IoT sensors, where PCB real estate is limited. Automotive applications include interior lighting control and non-critical switch interfaces, though not in safety-critical systems. Medical equipment manufacturers value it for expanding monitoring device interfaces while maintaining low power consumption.

Maintenance and Precautions

MAX7323ATE+T 电子元器件 MAXIM 封装BGA 批次25深圳市熠灿电子科技有限公司

Being a CMOS device, the MAX7323ATE+T requires standard ESD precautions during handling and installation. Proper PCB layout practices should be followed, including decoupling capacitors (0.1μF recommended) near the VCC pin and minimizing trace lengths for SDA/SCL lines to prevent signal integrity issues. When driving inductive loads (relays, motors), external protection diodes are advised to clamp voltage spikes. The interrupt output line should have a pull-up resistor if not internally enabled. For systems operating near the 1.7V minimum voltage, ensure stable power supply margins to prevent brownout conditions that could affect I²C communication reliability.

商家经验真实案例 · 安全可信
汽车解调器外贸
本文解析汽车解调器在外贸领域的市场现状、技术要点及采购建议,帮助从业者把握行业趋势,规避贸易风险,实现高效采购。

B2B Procurement Guide

When sourcing the MAX7323ATE+T, verify the supply chain authenticity as counterfeit semiconductor components are prevalent. Authorized distributors like Arrow, Avnet, and Digi-Key typically offer guaranteed genuine parts with full traceability. Consider minimum order quantities (MOQs) which commonly start at 100 pieces for tape-and-reel packaging. Lead times vary from stock availability to 8-12 weeks for full production runs. For prototype or small batch needs, broker markets may offer quicker access but with price premiums of 20-50% over volume pricing. Always request recent date codes to avoid obsolete inventory.

Related Manufacturers