Aicaigou LogoB2B WikiIndustrial Encyclopedia

LPC1114FBD48/301

Updated: 2026-07-16

Overview

The LPC1114FBD48/301 is a 32-bit microcontroller based on the ARM Cortex-M0 architecture, developed by NXP Semiconductors. It is designed for low-power, cost-sensitive embedded applications, offering a balance of performance and efficiency. With 32 KB of flash memory and 8 KB of SRAM, it is suitable for a wide range of industrial and consumer applications. The microcontroller operates at a maximum frequency of 50 MHz and includes a variety of peripherals such as GPIO, UART, SPI, I2C, and ADC. Its compact 48-pin LQFP package makes it ideal for space-constrained designs. The LPC1114FBD48/301 is widely used in automation, smart home devices, and IoT solutions due to its reliability and versatility.

Structure and Working Principle

C8051F MCU电源适配器 调试适配器 U-EC6 程序下载器 现货深圳市佰斯浩电子科技有限公司

The LPC1114FBD48/301 integrates an ARM Cortex-M0 core, which executes Thumb-2 instructions for efficient processing. The core is supported by on-chip flash memory for program storage and SRAM for data handling. Peripheral interfaces are connected via an AHB-Lite bus, ensuring low-latency communication. The microcontroller operates on a single power supply (1.8V to 3.6V) and includes power management features to minimize energy consumption. Its working principle revolves around fetching instructions from flash, executing them in the Cortex-M0 core, and interacting with peripherals to control external devices. Clock generation is handled by an internal RC oscillator or an external crystal, providing flexibility in timing requirements.

商家经验真实案例 · 安全可信
tds2024c低频测量法
本文针对TDS2024C示波器测量低于1Hz信号的难题,提供三种实用解决方案:硬件改造提升灵敏度、软件算法优化波形捕获、环境干扰排除技巧,帮助工程师突破低频测量瓶颈。

Key Features

The LPC1114FBD48/301 stands out for its low power consumption, making it suitable for battery-operated devices. It supports multiple power modes, including sleep and deep sleep, to further reduce energy usage. The microcontroller also features a nested vectored interrupt controller (NVIC) for efficient handling of real-time events. Other notable features include a 10-bit ADC for analog signal processing, multiple serial communication interfaces (UART, SPI, I2C), and up to 42 GPIO pins. Its compact footprint and robust design make it a preferred choice for embedded developers seeking a balance between performance and cost.

Application Areas

The LPC1114FBD48/301 is widely used in industrial automation for tasks such as motor control, sensor interfacing, and data acquisition. Its low power consumption and peripheral set make it ideal for consumer electronics like remote controls, smart watches, and home automation systems. In the IoT domain, this microcontroller is employed in edge devices for data collection and communication. It is also found in medical devices, automotive systems, and wearable technology, where reliability and efficiency are critical. The versatility of the LPC1114FBD48/301 ensures its relevance across diverse industries.

Maintenance and Precautions

PIC16F1519-I/MV 集成电路(IC) Microchip 工作温度 稳定性好深圳市云迪科技有限公司

To ensure longevity and reliability, the LPC1114FBD48/301 should be handled with ESD precautions during assembly and testing. Proper decoupling capacitors should be used near the power pins to stabilize the supply voltage. Developers should adhere to the operating voltage range (1.8V to 3.6V) to prevent damage. Firmware should be optimized to leverage power-saving modes when idle. Regular firmware updates and testing are recommended to address any potential issues. Thermal management is generally not a concern due to the microcontroller's low power dissipation, but adequate ventilation should be maintained in high-density designs.

商家经验真实案例 · 安全可信
pq3225参数解析
本文深入解析pq3225的关键参数,包括其性能特点、适用场景及常见疑问解答,帮助用户全面了解该产品的技术规格与实际应用价值。

B2B Procurement Guide

When procuring the LPC1114FBD48/301, buyers should verify the supplier's authenticity to avoid counterfeit products. NXP-authorized distributors are the most reliable sources. Bulk purchases often attract discounts, making it cost-effective for large-scale projects. Lead times can vary, so it's advisable to plan orders in advance, especially for high-volume requirements. Buyers should also consider the availability of development tools, such as evaluation kits and software libraries, to streamline the design process. Comparing prices across multiple suppliers can help secure the best deal.

Related Manufacturers