Aicaigou LogoAicaigou LogoB2B WikiIndustrial Encyclopedia

K4S561632D

Updated: 2026-07-31

Overview

The K4S561632D is a 256Mb (16Mx16) high-speed CMOS synchronous DRAM chip manufactured using advanced semiconductor technology. It operates at speeds up to 166MHz, making it suitable for applications requiring fast data access and processing. The device features a fully synchronous pipeline operation and is designed to be compatible with low-power systems. As an industrial-grade component, the K4S561632D offers reliable performance across a wide temperature range, typically from -40°C to 85°C. Its standardized interface allows for easy integration into various embedded systems and industrial control applications. The chip is commonly supplied in a 54-pin TSOP II package, which is widely used in the electronics industry.

Structure and Working Principle

F31L-1A7H1-11040 电子元器件 Amphenol(安费诺) 批次新年份深圳市英特法电子科技有限公司

The K4S561632D follows the standard SDRAM architecture with four internal banks that can be accessed independently. It uses a multiplexed address bus and a bidirectional data bus to communicate with the memory controller. The synchronous interface means all operations are referenced to a clock signal, allowing for precise timing control. The memory array is organized in rows and columns, with a burst access mode that enables efficient reading and writing of sequential data. Refresh operations are required to maintain data integrity, typically managed automatically by the memory controller. The device includes mode registers that can be programmed to optimize performance for specific applications.

商家经验真实案例 · 安全可信
摩托车整流器与继电器的区别
本文解析摩托车整流器和继电器在功能、工作原理及安装位置上的核心差异,帮助读者快速区分这两种关键电子元件,避免维修时的混淆。

Key Features

The K4S561632D offers several notable features that make it suitable for industrial applications. Its synchronous operation allows for precise timing control, while the burst access mode improves data throughput. The chip supports programmable burst lengths (1, 2, 4, 8, or full page) and features a CAS latency of 2 or 3. Power consumption is optimized through various low-power modes, including active standby and power-down modes. The device operates at 3.3V with TTL-compatible inputs and outputs. Its industrial temperature range (-40°C to 85°C) makes it reliable for harsh environments. The chip also includes auto refresh and self refresh capabilities for maintaining data without external intervention.

Application Areas

This SDRAM chip finds application in numerous industrial and embedded systems. It's commonly used in networking equipment such as routers and switches, where fast data buffering is required. Industrial automation systems utilize the K4S561632D for process control and data logging applications. The chip is also found in medical equipment, test and measurement instruments, and telecommunications infrastructure. Its reliability and performance make it suitable for applications requiring continuous operation under varying environmental conditions. Some consumer electronics with industrial-grade requirements may also incorporate this memory component.

Maintenance and Precautions

AD7799BRUZ AD7799BRU AD7799 TSSOP16 贴片原装芯片深圳市圣卡尔电子科技有限公司

Proper handling of the K4S561632D is essential for reliable operation. Electrostatic discharge (ESD) protection measures should always be used when handling the device. The chip should be stored in anti-static packaging when not in use, and work surfaces should be properly grounded. System designers should ensure the power supply provides clean, stable voltage within specified tolerances. Signal integrity must be maintained through proper PCB layout practices, including controlled impedance traces and adequate decoupling capacitors. The device should not be operated outside its specified temperature range, as this may affect reliability and data retention.

商家经验真实案例 · 安全可信
继电器NT90引脚定义
本文详细解析NT90系列继电器的引脚功能布局,包括线圈触点与负载端子的对应关系,以及常见型号的兼容性说明,帮助工程师快速完成电路设计。

B2B Procurement Guide

When procuring K4S561632D chips in bulk for industrial applications, several factors should be considered. Verify the manufacturer's authenticity and purchase from authorized distributors to avoid counterfeit components. Check for industrial-grade certification if the application requires extended temperature operation. Lead times can vary significantly depending on market conditions, so plan procurement accordingly. Consider requesting samples for testing before placing large orders. For long-term projects, discuss inventory management options with suppliers to ensure consistent supply. Pricing is typically volume-dependent, with discounts available for larger quantities (usually 100+ units).

Related Manufacturers