Aicaigou LogoAicaigou LogoB2B WikiIndustrial Encyclopedia

HC32F196MCTA

Updated: 2026-07-22

Overview

The HC32F196MCTA is a 32-bit microcontroller unit (MCU) based on the ARM Cortex-M0+ core, developed by HDSC (Huada Semiconductor). It is designed for applications requiring a balance of performance and power efficiency. With a clock speed of up to 48 MHz, it supports a wide range of peripherals, including ADCs, timers, and communication interfaces like UART, SPI, and I2C. This MCU is particularly suited for industrial control systems, consumer electronics, and IoT devices due to its low-power capabilities and robust feature set. It operates at a supply voltage of 1.8V to 5.5V, making it versatile for various power environments.

Structure and Working Principle

肖特基二极管MBRF10100CT现货直销深圳方恒电子科技有限公司

The HC32F196MCTA integrates an ARM Cortex-M0+ processor, which executes Thumb-2 instructions for efficient operation. It includes 64 KB of Flash memory and 8 KB of SRAM, providing sufficient storage for firmware and data. The MCU also features a nested vectored interrupt controller (NVIC) for handling multiple interrupts with low latency. Peripherals such as 12-bit ADCs, PWM timers, and communication modules enable it to interface with sensors, actuators, and other devices. The MCU supports multiple low-power modes, including sleep and deep sleep, to minimize energy consumption in battery-powered applications.

商家经验真实案例 · 安全可信
SEC是交流还是直流
本文解析SEC(二次侧)在电力系统中的电流类型,解释交流与直流的应用场景,并说明如何通过简单方法判断电气设备的工作电流性质。

Key Features

The HC32F196MCTA stands out for its low-power design, with active mode current as low as 100 µA/MHz and standby mode current below 1 µA. It includes hardware-based power management units to optimize energy usage. The MCU also offers a rich set of peripherals, including up to 16-channel 12-bit ADCs, multiple timers, and communication interfaces. Another notable feature is its robustness in industrial environments, with operational temperature ranges from -40°C to 85°C. It also includes ESD protection and noise immunity enhancements, making it suitable for harsh conditions.

Application Areas

The HC32F196MCTA is widely used in industrial automation, such as motor control, PLCs, and HMI systems. Its low-power capabilities make it ideal for battery-operated devices like smart sensors and wearable electronics. In consumer electronics, it powers appliances, remote controls, and lighting systems. IoT applications benefit from its communication interfaces and energy efficiency, enabling edge devices to connect seamlessly to networks. The MCU's versatility and reliability also make it a choice for medical devices and automotive subsystems.

Maintenance and Precautions

DIODES( LED驱动器(照明及背光) PAM2803AAF095 SOT23-6 21+深圳市盈腾兴电子科技有限公司

To ensure longevity, avoid exposing the HC32F196MCTA to voltages beyond its specified range. Proper ESD precautions should be taken during handling and soldering to prevent damage to sensitive components. Use recommended decoupling capacitors near power pins to stabilize supply voltages. Firmware should be optimized to leverage low-power modes effectively, reducing energy consumption in idle states. Regular debugging and testing are advised to identify potential issues early in the development cycle.

商家经验真实案例 · 安全可信
64脚贴片MCU拆卸技巧
本文详细介绍了64脚贴片MCU从线路板上安全拆卸的三种实用方法,包括热风枪加热、吸锡器辅助和低温焊锡技巧,帮助读者高效完成拆卸任务。

B2B Procurement Guide

When procuring the HC32F196MCTA, verify the supplier's authenticity to avoid counterfeit products. HDSC-authorized distributors are recommended for guaranteed quality. Bulk purchases typically offer cost savings, with prices ranging approximately $1.50-$3.00 per unit depending on volume. Evaluate the need for development tools, such as evaluation kits and debuggers, which can accelerate prototyping. Ensure compatibility with existing systems by reviewing peripheral requirements and power constraints before finalizing orders.

Related Manufacturers