Aicaigou LogoB2B WikiIndustrial Encyclopedia

GPIB Cable

Updated: 2026-08-03

Overview

The GPIB cable, standardized under IEEE 488, is a critical component in industrial and laboratory automation. Developed by Hewlett-Packard in the 1960s, it enables synchronous communication between up to 15 devices, such as signal generators and spectrum analyzers. Modern GPIB cables support bidirectional data transfer at speeds up to 8 MB/s, making them suitable for complex test benches. While newer interfaces like USB and Ethernet have emerged, GPIB remains widely used in legacy systems due to its reliability and standardized protocol.

Structure and Working Principle

四川 成都 富士(FUJIFILM )数据记录磁带 存储数据磁带库磁带机用 LTO7 LTO8 LTO9 富士清洗带(LTO-UCC-420)成都科汇科技有限公司

A GPIB cable consists of 24 twisted-pair wires with shielded connectors at both ends. The design includes 16 signal lines (8 data, 5 control, 3 handshake) and 8 ground lines to minimize interference. The bus operates on a byte-serial protocol, where one device acts as the controller (usually a computer) managing data flow. Devices can be daisy-chained, but total cable length must not exceed 20 meters. Termination resistors are often required to prevent signal reflections in long setups.

商家经验真实案例 · 安全可信
万用表测地线是否带电
本文详细介绍如何使用万用表检测地线是否带电,包括测量步骤、注意事项以及常见误区,帮助读者安全准确地完成检测。

Key Features

GPIB cables are prized for their deterministic latency, ensuring precise timing in automated measurements. Their rugged connectors feature locking mechanisms to prevent accidental disconnections. Key specifications include a maximum capacitance of 50 pF/m and impedance of 62–160 ohms. High-quality variants use double shielding (foil + braid) for EMI protection in noisy environments like factory floors. Some models include ferrite cores for additional noise suppression.

Application Areas

Primary applications include semiconductor testing, aerospace instrumentation, and automotive ECU validation. In R&D labs, GPIB networks integrate mixed-vendor equipment without custom drivers. The cables are also used in calibration systems for metrology-grade devices. Despite competition from LXI (LAN eXtensions for Instrumentation), GPIB persists in environments requiring real-time control, such as particle accelerator monitoring.

Maintenance and Precautions

长期供应美国原装 安捷伦4396B阻抗分析仪 Agilent晟希仪器(深圳)有限公司

Regularly inspect connectors for bent pins or worn contacts. Clean with isopropyl alcohol if oxidation is detected. Avoid coiling excess cable tightly, as this can degrade shielding effectiveness. For systems with multiple devices, ensure proper bus termination (typically 150-ohm resistors). Never hot-swap cables, as this may damage interface chips. Store cables loosely coiled in dry conditions to prevent insulation cracking.

商家经验真实案例 · 安全可信
示波器测电压原理
本文用通俗语言解析示波器测量电压的核心原理,从电子束偏转机制到信号处理流程,揭秘波形显示的物理本质,帮助读者建立直观认知。

B2B Procurement Guide

When sourcing GPIB cables, verify compatibility with your instrument models (e.g., Keysight, Tektronix). Industrial-grade cables with metal-shell connectors are recommended for harsh environments. Bulk purchases (10+ units) often attract 15–20% discounts. Lead times vary: standard cables ship in 1–2 weeks, while custom lengths may require 4 weeks. For obsolete systems, consider pre-owned cables from certified test/measurement resellers with warranty coverage.

Related Manufacturers