Aicaigou LogoAicaigou LogoB2B WikiIndustrial Encyclopedia

BL24C08A

Updated: 2026-07-29

Overview

The BL24C08A is an 8-Kbit serial Electrically Erasable Programmable Read-Only Memory (EEPROM) chip manufactured using CMOS technology. As a non-volatile memory solution, it retains data when power is removed and is commonly interfaced via the I2C protocol. The device finds widespread use in electronic systems requiring small amounts of reliable configuration storage. The chip operates across a broad voltage range (1.7V to 5.5V), making it suitable for both battery-powered and line-powered applications. With a storage endurance of 1 million write cycles and data retention of 100 years, it offers robust performance for industrial and commercial applications.

Structure and Working Principle

BL24C08A 电子元器件 上海贝岭 封装SOT23-10 批次24+深圳亚申科技有限公司

The BL24C08A consists of a memory array organized as 1024 × 8 bits, with built-in high-voltage generators for programming operations. The I2C interface uses a two-wire serial bus (SCL for clock and SDA for data) supporting standard (100kHz) and fast (400kHz) modes, with some variants reaching 1MHz. Internally, the chip incorporates write protection circuits, address comparison logic, and sequential read functionality. Data writes occur in byte or page (16-byte) modes, with automatic erase-before-write operation. The device employs an internal timer for write cycle completion, freeing the host processor from timing management.

商家经验真实案例 · 安全可信
电容是串联电路吗
本文解析电容在电路中的连接方式,明确串联与并联的区别,并详细说明如何在实际电路中正确接入电容,帮助读者理解电容的基本应用。

Key Features

The BL24C08A stands out for its low power consumption, drawing just 2mA during active operation and 5μA in standby mode. This makes it ideal for battery-powered IoT devices and portable electronics. The wide operating voltage range accommodates various system designs without requiring level shifting. Additional features include hardware write protection (via WP pin), built-in noise filtering on SCL/SDA inputs, and Schmitt trigger inputs for improved signal integrity. The device supports both industrial (-40°C to +85°C) and extended (-40°C to +125°C) temperature ranges, depending on the specific variant.

Application Areas

This EEPROM is widely used in smart home devices for storing configuration parameters and user preferences. In industrial automation, it serves for equipment calibration data and operational logs. Automotive applications include infotainment systems and electronic control units (ECUs) for non-critical data storage. The BL24C08A also appears in medical devices for parameter storage, consumer electronics like set-top boxes and smart TVs, and various embedded systems. Its small footprint (available in SOP8, DIP8, and TSSOP8 packages) makes it suitable for space-constrained designs across these diverse applications.

Maintenance and Precautions

BL24C08A-SFRC 电子元器件 TSSOP 数据手册 PDF 资料 规格书深圳市共奕科技有限公司

Proper handling of the BL24C08A requires standard ESD precautions during assembly and maintenance. The chip should not be subjected to voltages beyond its absolute maximum ratings (typically -0.3V to +6.5V on any pin). Designers should implement proper I2C bus termination and follow signal integrity best practices. When soldering, observe the recommended reflow profile (typically 260°C peak temperature for lead-free processes). For firmware implementation, include appropriate delays after write operations (typically 5ms) to ensure data integrity. The write protect (WP) pin should be properly managed to prevent accidental data corruption.

商家经验真实案例 · 安全可信
18uf电容换20uf行吗
本文探讨18uf电容替换为20uf电容的可行性,分析容量差异对电路性能的影响,并提供安全替换建议。

B2B Procurement Guide

When sourcing BL24C08A chips, verify the manufacturer's authenticity through authorized distributors due to prevalent counterfeits in the market. Key procurement considerations include package type (surface-mount vs. through-hole), temperature grade (industrial vs. extended), and minimum order quantities. Volume buyers should request factory certification and reliability test reports. Lead times typically range from 4-12 weeks for standard orders. Consider alternative part numbers (like AT24C08 or CAT24C08) for supply chain diversification, but verify compatibility through thorough testing before substitution.

Related Manufacturers