Aicaigou LogoB2B WikiIndustrial Encyclopedia

25LC256E/SN Serial EEPROM

Updated: 2026-07-21

Overview

The 25LC256E/SN is a 256Kbit (32KB) Serial EEPROM manufactured by Microchip Technology. It is part of the 25XX series, designed for applications requiring reliable non-volatile memory with minimal power consumption. The device communicates via a Serial Peripheral Interface (SPI), supporting clock frequencies up to 10MHz. Its compact 8-pin SOIC package makes it suitable for space-constrained designs. The 25LC256E/SN is widely adopted in automotive systems, medical devices, and industrial controls due to its robust performance across temperature extremes (-40°C to +85°C).

Structure and Working Principle

原装25LC256T-E/SN 存储IC MICROCHIP微芯 封装SOP8深圳市中芯巨能电子有限公司

The chip consists of a memory array organized as 32,768 x 8 bits, with a built-in page buffer for efficient write operations. Data transfers occur via four SPI signals: Chip Select (CS), Serial Clock (SCK), Serial Data Input (SI), and Serial Data Output (SO). The device implements advanced write protection features, including a hardware Write-Protect (WP) pin and software-controlled block protection. An internal write cycle timer manages the 5ms typical write time, eliminating the need for external polling during programming.

商家经验真实案例 · 安全可信
uc3845各脚功能解析
本文详细解析uc3845芯片各引脚功能,包括电源管理、信号输入输出等核心特性,帮助读者快速掌握其工作原理和应用要点。

Key Features

The 25LC256E/SN operates across a broad voltage range (1.8V to 5.5V), making it compatible with both 3.3V and 5V systems. Its standby current is typically just 1µA, while active read current measures 3mA at 5.5V, ideal for battery-powered devices. Additional features include sequential read mode for rapid data access, self-timed write cycles, and built-in noise protection for reliable operation in electrically noisy environments. The device meets AEC-Q100 automotive qualifications for harsh operating conditions.

Application Areas

Primary applications include automotive telematics for storing vehicle configuration data, medical devices for parameter retention, and industrial PLCs for program backup. It is also used in smart meters, IoT edge devices, and consumer electronics requiring firmware updates. In automotive systems, the chip often stores odometer data, ECU calibration parameters, and fault logs. Medical applications leverage its reliability for storing device calibration data and usage history, critical for regulatory compliance.

Maintenance and Precautions

25LC256E/SN 电子元器件 MICROCHIP/微芯 封装SOP8 批号24+深圳市纳艾斯科技有限公司

When integrating the 25LC256E/SN, designers should implement proper decoupling (typically 0.1µF ceramic capacitor near VCC) to ensure stable operation. Signal integrity measures like series termination resistors may be needed for long SPI traces. Avoid exceeding the maximum write endurance of 1 million cycles per sector by implementing wear-leveling algorithms in firmware. For high-reliability systems, consider periodic memory checksums to detect potential data degradation over extended periods.

商家经验真实案例 · 安全可信
tps2816工作原理
本文深入浅出地解析了tps2816的核心工作机制,从输入输出特性到内部保护功能,帮助读者全面理解这款设备的运行逻辑和应用场景。

B2B Procurement Guide

Industrial buyers should verify the device's date code and packaging (tape & reel vs. tube) based on production requirements. MOQ typically starts at 1,000 units for standard pricing, with lead times varying from stock availability to 12 weeks for large orders. For automotive applications, ensure suppliers provide full traceability documentation. Consider alternate part numbers like AT25256B from other manufacturers for second-source qualification. Evaluate programming service options for pre-loaded devices to streamline production.

Related Manufacturers