24C16A Serial EEPROM

Updated: 2026-07-17

Overview

The 24C16A is a widely used serial EEPROM (Electrically Erasable Programmable Read-Only Memory) chip that provides 16 kilobits (2 kilobytes) of non-volatile memory storage. Manufactured by various semiconductor companies, it has become an industry-standard component for applications requiring reliable, low-power data storage. This memory chip communicates via the I2C (Inter-Integrated Circuit) protocol, making it compatible with a wide range of microcontrollers and processors. Its small form factor and simple interface have made it particularly popular in consumer electronics, industrial controls, and automotive applications where configuration data or operational parameters need to be retained when power is removed.

Structure and Working Principle

BL24C16A 电子元器件 BL 封装SOP8 批次25+ 输入1.7~5.5V

深圳市华本天成电子有限公司

The 24C16A is organized as 256 pages of 8 bytes each, supporting both byte and page write operations. Internally, it consists of a memory array, address counter, and control logic that manages the I2C communication protocol. When writing data, the host controller sends a start condition followed by the device address and memory location. The chip then stores the data in the specified location, with typical write cycle times of 5ms. For reading, the controller requests data from specific addresses, which the 24C16A retrieves from its non-volatile memory cells. The device includes write protection features that can be enabled to prevent accidental data modification.

商家经验真实案例 · 安全可信

微芯片选型指南

本文从性能参数、应用场景和供应链适配三个维度，解析工业级微芯片选型的核心逻辑，帮助工程师避开常见误区，实现精准匹配需求的技术方案。

Key Features

The 24C16A offers several notable features that contribute to its widespread adoption. It operates across a broad voltage range (typically 1.7V to 5.5V), making it suitable for both low-power and standard voltage systems. The device consumes minimal current during operation (typically 1mA active, 1μA standby), an important consideration for battery-powered applications. Other significant features include a 1 million write cycle endurance and 100-year data retention capability. The chip supports clock frequencies up to 400kHz (Fast-mode I2C) and includes built-in noise protection filters for reliable operation in electrically noisy environments. These characteristics make the 24C16A a robust solution for critical data storage applications.

Application Areas

The 24C16A finds application in numerous electronic systems across various industries. In consumer electronics, it's commonly used in televisions, set-top boxes, and audio equipment to store configuration settings and user preferences. Industrial applications include programmable logic controllers, sensors, and measurement equipment where calibration data needs to be retained. The automotive industry utilizes these chips for storing vehicle configuration data, while medical devices employ them for equipment settings and usage logs. Other applications include smart meters, IoT devices, and computer peripherals where small amounts of non-volatile storage are required. The chip's reliability and long data retention make it suitable for these critical applications.

Maintenance and Precautions

深圳亚申科技有限公司

While the 24C16A is designed for reliable operation, proper handling and usage precautions should be observed. Electrostatic discharge (ESD) protection measures should be implemented during handling and assembly, as the device contains sensitive semiconductor components. When designing systems using this EEPROM, developers should implement proper write-cycle management to avoid exceeding the maximum specified write cycles prematurely. The device's address pins should be properly configured to avoid bus conflicts when multiple memory chips are used on the same I2C bus. Additionally, power supply decoupling capacitors should be placed close to the chip's VCC pin to ensure stable operation.

商家经验真实案例 · 安全可信

电压不稳能否充电

电压不稳定时充电可能影响设备电池寿命，但并非完全不能充电。本文分析电压波动对充电的影响，提供安全充电建议，并介绍应对电压不稳的实用方法。

B2B Procurement Guide

When procuring 24C16A chips in bulk for industrial applications, several factors should be considered. Verify the manufacturer's reputation and quality certifications, as counterfeit components can be a concern in the semiconductor market. Request samples for testing before placing large orders to confirm compatibility with your application. Consider ordering from authorized distributors to ensure genuine components and reliable supply chains. Lead times can vary depending on market demand, so plan procurement accordingly. For high-reliability applications, inquire about extended temperature range versions (-40°C to +125°C) which may be available from some manufacturers. Bulk pricing typically decreases significantly for quantities above 1,000 units.