Aicaigou LogoAicaigou LogoB2B WikiIndustrial Encyclopedia

24AA64T-I/MC

Updated: 2026-07-29

Overview

The 24AA64T-I/MC is a 64-Kbit (8-Kbyte) serial EEPROM memory device manufactured by Microchip Technology. It uses the I2C interface protocol, making it compatible with a wide range of microcontrollers and processors. This device is part of Microchip's extensive family of serial EEPROMs designed for embedded systems requiring reliable non-volatile memory. The 24AA64T-I/MC comes in an 8-lead MSOP package, offering a compact footprint suitable for space-constrained applications. It operates across a broad voltage range from 1.7V to 5.5V, supporting both low-power and standard voltage systems. The device features a 400 kHz clock frequency and supports both random and sequential read modes.

Structure and Working Principle

24AA64T-I/MC 存储IC Microchip(微芯) 批次24+深圳市万隆泰电子有限公司

The 24AA64T-I/MC consists of an array of floating-gate transistors that can be electrically erased and reprogrammed. The memory is organized as 8,192 words of 8 bits each, with a page size of 32 bytes for write operations. The I2C interface uses two wires (SDA and SCL) for communication with the host controller. The device incorporates several protection features including write protection pins and software write protection for partial or entire memory arrays. Data retention is specified for 200 years, and the device can endure at least 1,000,000 write cycles per byte. Internal circuitry handles all programming and erase voltages, eliminating the need for external high-voltage supplies.

商家经验真实案例 · 安全可信
tc7109原理
本文解析tc7109的工作原理,包括其核心功能、应用场景及技术特点,帮助读者理解这一技术的实际运作方式。

Key Features

The 24AA64T-I/MC offers several notable features that make it suitable for demanding applications. Its wide voltage range allows operation in battery-powered systems where voltage may vary significantly. The low standby current (1 µA typical) and active current (1 mA typical at 400 kHz) make it ideal for power-sensitive designs. Additional features include a built-in write protect pin that can disable all write operations when pulled high, and a software write protection scheme that can protect either 1/4, 1/2, or the entire memory array. The device also supports sequential reads for efficient data transfer and includes a noise protection circuit that rejects spikes on the bus lines.

Application Areas

This EEPROM is widely used across various industries due to its reliability and versatility. In automotive applications, it stores calibration data, configuration settings, and event logs. Industrial applications include parameter storage in sensors, actuators, and control systems where non-volatile memory is essential. Consumer electronics represent another major application area, with uses including firmware storage in smart home devices, user preference memory in appliances, and configuration data in portable electronics. The medical device industry also employs these EEPROMs for storing calibration data and usage logs in diagnostic equipment.

Maintenance and Precautions

24AA64T-I/MC 存储IC MICROCHIP/微芯 封装DFN 批号24+深圳市纳艾斯科技有限公司

Proper handling and usage of the 24AA64T-I/MC are crucial for ensuring reliability and longevity. ESD precautions must be observed during handling and assembly, as the device contains sensitive semiconductor components that can be damaged by static discharge. In system design, careful attention should be paid to I2C bus termination and pull-up resistor values to ensure reliable communication. The device should not be exposed to temperatures beyond its specified operating range (-40°C to +85°C) during use or storage. When designing for high-reliability applications, consider implementing error-checking or redundancy schemes to detect and correct potential data corruption.

商家经验真实案例 · 安全可信
tc7129引脚功能详解
本文详细解析tc7129芯片的各引脚功能,包括电源管理、信号输入输出及控制接口的具体作用,帮助读者快速掌握该芯片的核心应用方式。

B2B Procurement Guide

When procuring the 24AA64T-I/MC in bulk quantities, several factors should be considered to ensure optimal value and supply chain reliability. Verify the manufacturer's date code to ensure fresh inventory, as prolonged storage can potentially affect device performance. For high-volume purchases, consider negotiating pricing based on annual commitment quantities rather than one-time orders. Lead times for this device typically range from 8-12 weeks, so plan procurement accordingly. Always source from authorized distributors to guarantee authenticity, as counterfeit semiconductor components are a known industry issue. For prototype quantities, sample requests can often be made directly through Microchip's website or local sales representatives.

Related Manufacturers